HPE0-S59 Dumps for Pass Guaranteed - Pass HPE0-S59 Exam 2023
HPE0-S59 Exam Dumps - Try Best HPE0-S59 Exam Questions from Training Expert Free4Dump
NEW QUESTION # 31
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard licenses for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options Which statement about this proposal is true?
- A. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
- B. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.
- C. vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
- D. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
Answer: C
NEW QUESTION # 32
Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?
- A. The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.
- B. The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.
- C. The customer can add a new logical enclosure to an existing setup once all required licenses are added lo HPE OneView and associated with the new frames.
- D. The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.
Answer: D
NEW QUESTION # 33
Which compute node parameters are captured within server hardware type?
- A. Mezzanine card configuration
- B. Number of the CPUs
- C. Size of the memory Installed
- D. installed operating system
Answer: D
NEW QUESTION # 34
Which statement about login redistribution is true?
- A. Login redistribution is used for login balancing when they are not distributed evenly over the FC links
- B. Login redistribution is available only If HPE Primera or HPE Alletra is connected directly to the HPE Synergy frame
- C. Login redistribution is a licensed feature and the number of licenses required depends on the number of active ports
- D. Login redistribution is supported only on the HPE Synergy Virtual Connect SE 32Gb FC Modules
Answer: D
NEW QUESTION # 35
Which statement about a new HPE SimpliVity deployment is true?
- A. New HPE SimpliVity deployments give customer flexible choice of hypervisor
- B. All new HPE SimpliVity models support deduplication and compression
- C. All new HPE SimpliVity models are based on AMD CPUs
- D. New HPE SimpliVity deployments are licensed per node not per physical socket
Answer: B
NEW QUESTION # 36
What is a restriction of using a RoCE network?
- A. it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
- B. It does not support smart link and private network features.
- C. It is by default configured as an untagged network and cannot be a part of a network set.
- D. It does not support Private VLAN and Multicast VLAN.
Answer: C
NEW QUESTION # 37
Which statement about the HPE D3940 storage module is true?
- A. Only one type of drives (SATA, SAS, SSD) can be installed in each module
- B. it is configured through CLl available from HPE Synergy console
- C. Up to five modules can be installed in a single frame with Gen10 servers
- D. SATA drives requires redundant 10 adapters to be installed in this module
Answer: B
NEW QUESTION # 38
Which statement about the SY480 Gen10 Plus Compute Module is true?
- A. It supports "3rd Gen AMO EPYC Server Processors with 64 cores.
- B. It cannot be mixed with Gen9 compute modules in the same frame.
- C. It only supports NVDIMM Persistent Memory.
- D. It supports 8 memory channels and memory DIMMs of up to 256GB.
Answer: C
NEW QUESTION # 39
Which statement about an HPE Oneview support dump is true?
- A. Support dump can be created if HPE Virtual Connect modules are installed in the frame
- B. Appliance support dump by default contains a logical enclosure support dump
- C. Preview support dump is available only when creating an appliance support dump
- D. Support dump is a binary file that can be opened only in a dedicated application
Answer: D
NEW QUESTION # 40
Your customer reports that they cannot deploy HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC).
What should you check during troubleshooting process?
- A. If HPE OneView credentials are added in vCenter Server
- B. If an compute nodes are added to the vCenter Server
- C. If the HPE Oneview instance Is integrated with HPE OV4VC.
- D. If vCenter Server is licensed in the HPE Oneview interface
Answer: B
NEW QUESTION # 41
Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.
Answer:
Explanation:
NEW QUESTION # 42
An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays Where should you start the troubleshooting process?
- A. At the iLO interface to verify whether the SSO certificate is removed from an iLO.
- B. At HPE OneView Interface to verify whether the server is In the maintenance mode
- C. At the iLO interface to verify whether the ILO Advanced license is properly applied
- D. At HPE OneView Interface to verify whether the iLO processor is disabled
Answer: C
NEW QUESTION # 43
After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.
Answer:
Explanation:
NEW QUESTION # 44
Your customer is implementing an HPE Synergy solution based on three frames.
Click each of the ports that can be used to connect satellite modules.
Answer:
Explanation:
NEW QUESTION # 45
Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup.
Which procedures should De performed during the expansion process? (Select two.)
- A. Modify an existing logical interconnect to include second HPE Synergy frame.
- B. Create a new logical interconnect group and enclosure group for two frames setup
- C. Re-parent an existing enclosure group to the new logical interconnect group.
- D. Create a new logical enclosure based on both HPE Synergy frames.
- E. Move one of the master modules to the appropriate interconnect bay in the second frame.
Answer: A,D
NEW QUESTION # 46
A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?
- A. HPE Virtual Connect SE 100 Gb F32 Module tor Synergy
- B. HPE Synergy 12 Gb SAS Connection Module
- C. Brocade 32GB Fibre Channel Switch Module for HPE Synergy
- D. HPE virtual Connect SE 32 Gb FC Module for Synergy
Answer: A
NEW QUESTION # 47
Match HPE SimpliVity team with the definition.
Answer:
Explanation:
NEW QUESTION # 48
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A. For an uplink set, ports from different modules can be selected
- B. interconnect modules are installed in interconnect bays 1 and 4
- C. Both modules are located in different frames for redundancy
- D. An additional license is required to change the enclosure count
Answer: D
NEW QUESTION # 49
Which statement about HPE OneView milestone releases is true?
- A. A milestone release is available for selected partners that give access to HPE OneView features which are not officially announced.
- B. A milestone release is a release which must be installed on HPE Composer to support current version of the Service Pack for Synergy
- C. A milestone release is a release that is published when HPE releases new hardware components to immediately support new systems
- D. A milestone release is a release with an enhanced update architecture mat is a prerequisite prior to updating to a subsequent release.
Answer: B
NEW QUESTION # 50
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)
- A. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- B. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- C. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- D. Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
- E. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
- F. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
Answer: C,F
NEW QUESTION # 51
You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?
- A. App Volume Set
- B. Virtual Volume Set
- C. virtual Volume
- D. Storage Container
Answer: B
NEW QUESTION # 52
......
Latest 100% Passing Guarantee - Brilliant HPE0-S59 Exam Questions PDF: https://www.free4dump.com/HPE0-S59-braindumps-torrent.html
Practice Examples and Dumps & Tips for 2023 Latest HPE0-S59 Valid Tests Dumps: https://drive.google.com/open?id=1bpwbOJbAV1ENMDBIFPbn1AZ5kN1arF5g