100% Guaranteed Results NACE-CIP2-001 Unlimited 100 Questions [2021]
NACE-CIP2-001 Dumps PDF - Want To Pass NACE-CIP2-001 Fast
NEW QUESTION 37
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. coating type.
- C. manufacturer of the equipment.
- D. time of the year (winter/summer).
Answer: B
NEW QUESTION 38
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Application Costs
- B. Lower Safety Enforcement Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Supervision Costs
Answer: C
NEW QUESTION 39
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that another NACE Inspector would understand
- B. Language that the most would understand
- C. Language that only technical experts would understand
- D. Language that only in the project would understand
Answer: B
NEW QUESTION 40
Coating application to concrete substrates is:
- A. Less challenging, than coating steel
- B. Not required as Concrete is inorganic
- C. More challenging than coating steel
- D. The same as coating steel
Answer: C
NEW QUESTION 41
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. inorganic zincs.
- B. urethanes.
- C. epoxies.
- D. powder coatings.
Answer: A
NEW QUESTION 42
All of these are advantages of using repair patches EXCEPT
- A. excellent abrasion resistance.
- B. special tools or equipment are required.
- C. barrier to moisture and corrosion.
- D. inert to common acids, alkalis, and solvents.
Answer: B
NEW QUESTION 43
Surface preparation methods for Non-ferrous metals are:
- A. Not required
- B. The same as for Ferrous metals
- C. Specific for each type of Non-ferrous metal
- D. The same for all Non-FetT0us metals
Answer: C
NEW QUESTION 44
In which type of concrete are laitance commonly encountered?
- A. Concrete block (poured with a form)
- B. Poured (wet cast)
- C. Glass fiber cement
- D. Gunite
Answer: B
NEW QUESTION 45
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Standard buffer solution
- C. Deionized water
- D. Standard solvent solution
Answer: B
NEW QUESTION 46
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Re-create the reports as not much was going on during night shift anyway
- C. Use creative writing to cover over the fact they are missing
- D. Plainly state in your report that they are missing
Answer: D
NEW QUESTION 47
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Stop the job immediately
- C. Request that the item be rebuilt with a better design for coating
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION 48
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Move the nozzle quicker
- D. Increase the standoff distance
Answer: A
NEW QUESTION 49
The HATE adhesion tester uses
- A. compressed air to apply pressure to the test dolly.
- B. mechanical means only to apply pressure to the test dolly.
- C. a hydraulic piston to apply pressure to the test dolly.
- D. a special tape to apply pressure to the test dolly.
Answer: C
NEW QUESTION 50
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. coatings are more durable than linings.
- C. linings protect the contents and the container.
- D. coatings are expected to degrade over time.
Answer: C
NEW QUESTION 51
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage AC
- B. Low Voltage Sponge Type
- C. High Voltage DC Constant Current
- D. High Voltage DC Pulse Type
Answer: C
NEW QUESTION 52
You can use magnifiers to examine all of the following EXCEPT
- A. Surface profile
- B. Blisters
- C. Surface cleanliness
- D. Mill scale
Answer: C
NEW QUESTION 53
Inspection and Test Plans are provided to:
- A. So the contractor has a single document to reference
- B. To supersede the requirements of the product data sheets
- C. So the Inspector doesn't have to read the entire specification
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 54
A reinforced coating is
- A. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to abrasion and impact as a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. more resistant to movement, abrasion, and impact than a non-reinforced coating.
Answer: D
NEW QUESTION 55
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Use the correct solvent
- C. Record the highest value attained
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION 56
The Concrete Repair Institute's comparators can be used to assess:
- A. Compressive and tensile strength prior to coating
- B. Surface profile prior to coating
- C. Surface cleanliness prior to coating
- D. Contamination levels prior to coating
Answer: B
NEW QUESTION 57
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Cost
- C. Safety
- D. Iron content
Answer: D
NEW QUESTION 58
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION 59
When environmental enclosures are being used an inspector needs to be concerned about:
- A. a), b), and c)
- B. Lighting
- C. Air changes
- D. Structural integrity
Answer: A
NEW QUESTION 60
......
Updated Verified NACE-CIP2-001 Q&As - Pass Guarantee: https://www.free4dump.com/NACE-CIP2-001-braindumps-torrent.html
NACE-CIP2-001 Practice Exam Dumps - 99% Marks In NACE Exam: https://drive.google.com/open?id=1dW8RGPGBrW_5aFTjeG-M9OioAmMQXvZ-