100 Q&As in UPDATED NACE-CIP1-001 Exam Questions Certification Test Engine to PDF
Get The Important Preparation Guide With NACE-CIP1-001 Dumps
NACE-CIP1-001 Certification Exam is a rigorous assessment that requires candidates to master a wide range of topics, including the characteristics of coating materials, surface preparation techniques, coating application methods, and safety procedures. NACE-CIP1-001 exam consists of 100 multiple-choice questions and candidates have three hours to complete it. The questions are designed to test the candidate's understanding of the principles of coating inspection and their ability to apply this knowledge to real-world situations.
NEW QUESTION # 46
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Presence of weld spatter may produce a false positive
- C. Chloride salt may produce a false positive
- D. Ultra-Violet light may contaminant the surface
Answer: A
NEW QUESTION # 47
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. The information aids communication with supervisors.
- C. Inspectors rarely change on a project.
- D. Management uses them to make personnel decisions.
Answer: A,B,D
NEW QUESTION # 48
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: D
NEW QUESTION # 49
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. In every instance that an item does not meet the specification requirements
- D. In accordance with the specification's definition of a non-conformance
Answer: B
NEW QUESTION # 50
Stripe coats are best applied by:
- A. Brush
- B. Airless spray
- C. High volume low pressure spray
- D. Conventional spray
Answer: A
NEW QUESTION # 51
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he can proceed
- B. Advise the Contractor of your readings
- C. Advise the Contractor he cannot proceed
- D. Call your supervisor
Answer: B
NEW QUESTION # 52
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. blistering.
- C. alligatoring.
- D. checking.
Answer: D
NEW QUESTION # 53
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Stainless steel pipe to be Externally Coated
- C. Structural steel to be coated for Atmospheric Service
- D. Tanks and Vessels to, be Lined for Immersion Service
Answer: D
NEW QUESTION # 54
The Inspector should record the serial numbers of inspection instruments:
- A. Only if the instrument is suspected of not working properly
- B. Each time the instrument is used
- C. Only when verifying accuracy of the instrument
- D. Only if the specification requires it
Answer: B
NEW QUESTION # 55
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Bring the matter up at the pre-job conference
- C. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
Answer: B
NEW QUESTION # 56
Polymerization is the process of:
- A. Monomers joining together
- B. All organic coatings
- C. All thermoplastic coatings
- D. Monomers telegraphing
Answer: A
NEW QUESTION # 57
Inspector's daily reports are used:
Select All That Apply
- A. To aid in arbitration between the contractor and client
- B. By the contractor to estimate the amount of work done that day
- C. To provide continuity between inspectors
- D. To help in cases of a coating failure
Answer: A,B,C,D
NEW QUESTION # 58
Which one of these elements is not necessary for corrosion to occur:
- A. Cathode
- B. Anode
- C. Electrolyte
- D. Reference Cell
Answer: D
NEW QUESTION # 59
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: A
NEW QUESTION # 60
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Profilometer
- C. Psychrometer
- D. Needle pressure gauge
Answer: B
NEW QUESTION # 61
Osmotic blistering is most likely to occur as a result of
- A. inadequate anchor pattern/surface profile.
- B. airless spray application
- C. applying tine coating too thin.
- D. overcoating a surface contaminated with chemical salts.
Answer: B
NEW QUESTION # 62
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Soften when heated and return to its original hardness when cooled
- C. Harden and return to its original hardness when cooled
- D. Harden and retain its hardness when cooled
Answer: D
NEW QUESTION # 63
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. pigment
- C. binder
- D. additive
Answer: C
NEW QUESTION # 64
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
Answer: A,B
NEW QUESTION # 65
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
Answer: D
NEW QUESTION # 66
The most important factor resulting in improved job site safety is:
- A. Personal Protective Equipment
- B. Situational Awareness
- C. Safety Enforcement
- D. Engineering Controls
Answer: B
NEW QUESTION # 67
......
Prepare With Top Rated High-quality NACE-CIP1-001 Dumps For Success in Exam: https://www.free4dump.com/NACE-CIP1-001-braindumps-torrent.html
Get Totally Free Updates on NACE-CIP1-001 Dumps PDF Questions: https://drive.google.com/open?id=1dQW08hcI9jxKNqOiyjpJXYms-mCHTCGQ